×ðÁú¿­Ê±×îÐÂƽ̨µÇ¼

±ê×¼¹âÄ£¿é

±ê׼ЭÒé¹âÄ£¿é

¼æÈÝЭÒé¹âÄ£¿é

ÆäËüÖÖÀà¹âÆ÷¼þ

ÊÖÒÕÖ§³Ö

10G SONET SFP+ ER Transceiver

10G SONET SFP+ ER Transceiver

0.0/5 rating (0 votes)

Description

Description

The FT-MTRS-2S60-01 is a very compact 10Gb/s optical transceiver module for serial optical communication applications at 10Gb/s. The MTRS-2S60-01 series converts a 10Gb/s serial electrical data stream to 10Gb/s optical output signal and a 10Gb/s optical input signal to 10Gb/s serial electrical data streams. The high speed 10Gb/s electrical interface is fully compliant with XFI specification (built in CDR on both TX and RX) and allows FR4 host PCB trace up to 200mm. The FT-MTRS-2S60-01 is designed for use in a variety of 10Gb/s equipment SDH/SONET (9.95Gb/s), Ethernet LAN (10.3Gb/s) and FC (10.5Gb/s). The customer can adjust interface electrical level to select 9.95G~11.3G rate section. The high performance 1550nm DFB transmitter coupled with a high sensitivity PIN receiver provide superior performance for applications up to 40km SMF.The fully compliant SFP form factor provides high density applications, hot plug ability easy optical port upgrades and low EMI emission.

The SFP+ ER with CDR module electrical interface is compliant to XFI electrical specifications. The transmitter input and receiver output impedance is 100Ohms differential. Data lines are internally AC coupled.The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI.

Features

¡ñ  10Gb/s serial optical interface compliant to SONET OC-192/SDH STM-64 and 802.3ae

¡ñ  Electrical interface compliant to SFF-8431 specifications for 10 Gigabit small form factor pluggable module “SFP+”

¡ñ  1550nm cooled EML transmitter with TEC, PIN receiver

¡ñ  2-wire interface for management specifications compliant with SFF-8472 digital diagnostic monitoring interface for optical transceivers

¡ñ  Operating case temperature: 0°C~70°C

Applications

¡ñ  SONET(OC-192)/SDH(STM-64) line card

¡ñ  10GBASE-ER (10.3125Gbps)

¡ñ  10GBASE-EW (9.953Gbps)

Compliance

¡ñ  Compliant with IEEE 802.3ae-2002 10G Base-ER

¡ñ  Compliant with SFF-8431 & SFF-8432 & SFF-8472

Specification

Table1-Absolute Maximum Ratings

Paramete

Symbol

Min.

Max.

Unit

Storage Temperature

Ts

-40

+85

¡æ

Operating Case Temperature

Tc

-5

+75

¡æ

Supply Voltage

Vcc

0

+4

V

Relative Humidity

RH

+5

+85

%

Rx Input Average Power

Pmax

-

0

dBm

Table2-Recommended Operating Conditions

Paramet

Symbol

Min.

Typical

Max.

Unit

Operating Case Temperature

TC

0

25

+70

¡æ

Power Supply Voltage

VCC3

3.135

3.3

3.465

V

Power Supply Current

ICC3

-

-

545

mA

Power Consumption

-

-

1800

mW

Table3-Transmitter Operating Characteristic-Optical

Parameter

Symbol

Min

Typical

Max

Unit

Note

Operating Data Rate

DR

9.95

-

11.3

Gb/s

Output Center Wavelength

λ c

1530

1550

1565

nm

Side Mode Suppression Ratio

SMSR

30

-

dB

Average Output Power

Po

-1

+2

dBm

Disabled Power

Poff

-

-30

dBm

Extinction Ratio

ER

8.2

-

dB

Eye Mask (@SONET/SDH)

-

5%   (1000 consecutive snapshots at typical rate and room temperature)

%

Generation Jitter 1 (20kHz - 80MHz)

-

-

-

0.3

UIp-p

Generation Jitter 2 (4MHz - 80MHz)

-

-

-

0.1

UIp-p

Relative Intensity Noise

RIN

-

-

-128

dB/Hz

Operating Distance

-

-

40

-

km

Transmitter and dispersion penalty

-

-

-

2

dB

Spectral Width

-

-

-

0.5

nm

Dispersion tolerance

Dt

-

-

800

Ps/nm

Optical return loss tolerance

-

21

dB

Table4-Receiver Operating Characteristic-Optical

Parameter

Symbol

Min

Typical

Max

Unit

Note

Operating Data Rate

-

9.95

-

11.3

Gb/s

Input Center Wavelength

lrc

1260

1605

nm

Overload

Rovl

-1

-

-

dBm

Minimum Sensitivity

Rsen

-

-

-16

dBm

RX_LOS Assert Level

RLOSa

-28

-

-

dBm

RX_LOS Deassert Level

RLOSd

-

-

-18

dBm

RX_LOS Hysteresis

RLOSh

0.5

-

dB

Optical Return Loss

ORL

-

-

-27

dB

Table 5-Eelectrical characteristics

Parameter

Symbol

Min

Typical

Max

Unit

Note

Input differential impedance

-

100

Ω

Differential data input swing

VI

180

700

mV

Differential data output swing

  V0

300

850

mV

Tx Fault, LOS Output Voltage                           

High               Low

-

2.4

Vcc

V

Low

-

Vee

Vee+ 0.4

V

Tx DisableRS0,RS1    

     Low                      High

VIL

Vee-0.3

Vee+ 0.8

V

High

VIH

2

Vcc+0.3

V

DITITAL DIAGNOSTIC FUNCTIONS

The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless therwise specified. It is compliant to SFF-8472 Rev10.4 with internal calibration mode. For external calibration mode please contact our sales stuff.

Table 6- Digital diagnostic specification table

Parameter

Symbol

Min.

Max

Unit

Notes

Temperature monitor

absolute error

DMI_Temp

-3

3

degC

Over operating

temp

Laser power monitor

absolute error

DMI_TX

-2

2

dB

RX power monitor absolute

error

DMI_RX

-2

2

dB

-1dBm to

-16dBm range

Supply voltage monitor

absolute error

DMI_VCC

-3

3

%

Bias current monitor

DMI_Ibias

-10%

10%

mA

 

 

 

 

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.

Search

ÍøÕ¾µØͼ