×ðÁú¿­Ê±×îÐÂƽ̨µÇ¼

±ê×¼¹âÄ£¿é

±ê׼ЭÒé¹âÄ£¿é

¼æÈÝЭÒé¹âÄ£¿é

ÆäËüÖÖÀà¹âÆ÷¼þ

ÊÖÒÕÖ§³Ö

25G 1310nm 10km SM SFP28 Transceiver

25G 1310nm 10km SM SFP28 Transceiver

0.0/5 rating (0 votes)

Description

Description

FT-MTRA-3E30Ais a high performance, cost effective modules, which is supporting Multi Rate 9.953-25.78Gbps, and transmission distance up to 10km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a 1310nm DFB Laser, a driver and a CDR. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA), a Limitting Amplifier and CDR. The module is hot pluggable into the 20-pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module.

The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Transmit Fault (Tx_Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser operation or safety. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver.  

A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire SFP

Management Interface. Digital diagnostics function are available via a 2-wire serial interface, as specified in SFF-8472.

Features

¡ñ  Up to 10KM transmission distance

¡ñ  Support Multi Rate 9.953-25.78Gbps

¡ñ  1310nm DFB and PIN receiver

¡ñ  SFI electrical interface

¡ñ  2-wire interface for integrated Digital Diagnostic monitoring

¡ñ  SFP+ MSA package with duplex LC connector

¡ñ  H ot pluggable

¡ñ  Very low EMI and excellent ESD protection

¡ñ  +3.3V power supply

¡ñ  Power consumption less than 1.5W

¡ñ  Operating case temperature: 0~70°C

Applications  

¡ñ  25Gbps Ethernet

Compliance  

¡ñ  Compliant with IEEE 802.3-2012

¡ñ  Compliant with FCC 47 CFR Part 15, Class B

¡ñ  Compliant with MSA SFF-8472

¡ñ  Compliant with MSA SFF-8431

Specification

Absolute Maximum Ratings

Parameter

Symbol

Min.

Max.

Unit

Storage Temperature

TS

-40

85

¡æ

Supply Voltage£¨no damaged£©

VCC3

-0.5

3.6

V

Relative Humidity(non-condensing)

RH

5

95

%

RX Input OMA Power

Pmax

5

dBm

Recommended Operating Conditions

Parameter

Symbol

Min.

Typical

Max.

Unit

Operating Case Temperature

TC

0

25

70

¡æ

Power Supply Voltage

VCC3

3.135

3.3

3.465

V

ICC3

400

mA

Power Dissipation

PD

1.2

1.5

W

Data Rate(NRZ)

24.33

25.78

Gbps

Transmission Distance

10

Km

Transmitter Operating Characteristic-Optical, Electrical

Parameter

Symbol

Min.

Typical

Max.

Unit

Note

Centre Wavelength

λC

1290

1310

1325

nm

Side Mode Suppression Ratio  

SMSR

30

dB

Laser Off Power

Poff

-30

dBm

Average Optical Power

Pavg

-4.5

4.5

dBm

Extinction Ratio

ER

4

dB

Transmitter Dispersion Penalty

2.7

dB

Relative Intensity Noise

Rin

-130

dB/Hz

Optical Return Loss Tolerance

12

dB

Operating Data Rate

24.33

25.78

Gbps

Note1

Optical Eye Mask

>5% (Compatible 100GBASE-LR4)

Note 2

Common mode voltage tolerance

15

mV

Tx Input Diff Voltage

VI

200

500

900

mV

Tx Fault

VOL

0.4

V

At 0.7mA

Note3

VOH

VccT-0.4

Notes:

[1]Under CDR bypass mode, CPRI option 7 compatibility

[2] 1000 consecutive snapshots at typical rate and room temperature

[3] Measured with a 4.7k Ohm load pulled up to Vcc

 

 

 

 

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.

Search

ÍøÕ¾µØͼ